With respect to blend out repairs, is it required to record the depth and area dimensions of material removed during a blend out repair or is it sufficient to simply record that the damage has been repaired as per the SRM?
Yes, the dimensions of the damage and the removed/remaining material should be recorded. This is a very important information in order to assess whether further damage (adjacent or at the same spot) at a later stage would be allowable or not. In addition, it is a safeguard measure in order to be able to determine, during audits, whether the person correctly determined that the damage was within limits.
Can the subcontractor of a Part-145 or Part-CAO organisation release maintenance?
One of the fundamentals of subcontracting activities is that, during such maintenance, the Part-145 approval is extended to include the subcontractor activities. Subcontracting can be done only if the Part-145 has approved procedures to do it (145.A.75(b)) and the MOE is amended to reflect this new subcontractor.
A certificate of release to service can be issued by a person from the subcontractor who has received a certification authorisation from the Part-145 organisation in accordance with the certification authorisation procedure of the MOE including the assessment of competence.
The certificate of release to service and the EASA Form 1 will always be issued under the maintenance organisation approval reference.
For maintenance by Part-CAO the situation is different. Only ‘specialised services’ (e.g. NDT) can be subcontracted to another organisation, in accordance with the appropriate procedure set out in the CAE and approved by the competent authority (CAO.A.095(a)(2)). In accordance with AMC1 CAO.A.025 the procedure should be part of chapter B.7 ‘Subcontracting’.
A certificate of release to service can be issued by a person from the other organisation who has received a certification authorisation from the CAO in accordance with the certification authorisation procedure of the CAE.
The certificate of release to service will always be issued under the CAO approval reference.
Release to service of NDT tasks by Part-145 or Part-CAO organisations
This answer is separated in two tables. One table is for organisation holding a Part-145 approval and the second table is for organisations holding a Part-CAO approval.
Part-145:
|
Part-145 organisation |
Certifying staff required |
Qualification system |
General Release procedure |
Release procedure for an NDT inspection |
|---|---|---|---|---|
|
Aircraft
|
The release of the aircraft maintenance carried out under A class rating has to be performed by certifying staff holding a Part-66 licence. (B1 or B3 or C or L certifying staff under the organisation’s A rating.) |
Licencing of personnel has to follow Part-66 regulation. |
The release is either on the aircraft technical log or issuing an aircraft release to service statement. |
A Part-145 organisation holding an A approval rating on a particular aircraft type and having in its approved scope of work NDT inspections for this aircraft type.
This organization needs to have part-66 certifying staff and NDT personnel qualified in accordance with 145.A.30(f).
In this case the NDT inspector performs the NDT task and signs off the work order. The aircraft is released by appropriately qualified B1, B3, C or L certifying staff under the organisation’s A rating.
Please note that the release may include not only the NDT task but also the associated tasks (removal of panels, blankets, wires, re-installation, etc), or the NDT task may be part of a base maintenance check.
|
|
Engines
|
The release of the engine maintenance carried out under B class rating has to be performed by engine’s certifying staff. |
The certifying staff is qualified following the procedures established by the organisation in compliance with the competent authority requirements. Part-66 licence is not required. |
The release of works performed under class B is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the MOE). |
A Part-145 organisation holding a B rating approval on a particular engine type and having in its approved scope of work NDT inspections for this engine type. This organization needs to have “engine” certifying staff (qualified in accordance with company procedures) and NDT personnel qualified in accordance with 145.A.30(f). In this case the NDT inspector performs the NDT task and signs off the work order. The engine certifying staff releases the works performed to the engine (including NDT inspection) on an EASA Form 1.
|
|
Components |
The release of the component maintenance carried out under C class rating has to be performed by components certifying staff (CCS). |
The certifying staff is qualified following the procedures established by the organisation in compliance with the competent authority requirements. The CCS is not required to have a Part-66 licence. |
The release of works performed under class C is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the MOE). |
A Part-145 organisation holding a C rating approval on a particular component and having in its approved scope of work NDT inspections for this component. This organization needs to have CCS and NDT personnel qualified in accordance with 145.A.30(f). In this case the NDT inspector performs the NDT task and signs off the Work Order / Engineering Order. The CCS releases the works performed to the component (including NDT inspection) on an EASA Form 1. |
|
Specialised services |
The release of the maintenance carried out under D1 class rating has to be performed by “specialised services” certifying staff. |
The certifying staff is qualified following the procedures established by the organisation in compliance with EN4179, Part-66 licence is not required. |
The release of works performed under class D1 rating is done on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the MOE in compliance with 145.A.50 and approved by the competent authority. |
A Part-145 organisation holding a D1 approval on a particular NDT method. The approved scope of work will be NDT inspections on this method. This organisation needs to have NDT certifying staff qualified in accordance with 145.A.30(f). In this case the NDT certifying staff performs and releases the NDT task on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the MOE in compliance with 145.A.50 and approved by the competent authority. |
Note: In case of non-EU organisations approved by the EASA in accordance with Part-145, the Part-66 licence could be read as “Part-66 or national licence in accordance with Part-145 Appendix IV”
Part-CAO:
|
Part-145 organisation |
Certifying staff required |
Qualification system |
General Release procedure |
Release procedure for an NDT inspection |
|---|---|---|---|---|
|
Aircraft
|
The release of the aircraft maintenance carried out under A class rating has to be performed by certifying staff holding a Part-66 licence. |
Licencing of personnel has to follow Part-66 regulation. |
The release is either on the aircraft technical log or issuing an aircraft release to service statement. |
A Part-CAO organisation holding an aeroplanes, helicopter, airships, balloons or sailplanes particular aircraft type or and having in its approved scope of work NDT inspections for this aircraft type.
This organization needs to have part-66 certifying staff and NDT personnel qualified in accordance with CAO.A.035(f). In this case the NDT inspector performs the NDT task and signs off the work order. The aircraft is released by appropriately qualified B1, B3 or L certifying staff under the organisation’s aeroplanes, helicopter, airships, balloons or sailplanes rating. Please note that the release may include not only the NDT task but also the associated tasks (removal of panels, blankets, wires, re-installation, etc), or the NDT task may be part of a base maintenance check. |
|
Engines or Components other than complete engines
|
The release of the engine maintenance carried out under components class rating has to be performed by ‘engine’s’ or ‘components other than complete engines‘ certifying staff. |
The certifying staff is qualified following the procedures established by the organisation, Part-66 licence is not required. |
The release of works performed under class components is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the CAE). |
A Part-CAO organisation holding a components rating approval on a particular engine type or ‘components other than complete engines‘ and having in its approved scope of work NDT inspections for this engine type.
|
|
Components |
The release of the component maintenance carried out under C class rating has to be performed by components certifying staff (CCS). |
The certifying staff is qualified following the procedures established by the organisation in compliance with the competent authority requirements. The CCS is not required to have a Part-66 licence. |
The release of works performed under class C is done on an EASA Form 1 (or by means of an internal release document when this component is for the organisation’s own use and the organisation has in place the related internal procedures in the MOE). |
A Part-145 organisation holding a C rating approval on a particular component and having in its approved scope of work NDT inspections for this component. This organization needs to have CCS and NDT personnel qualified in accordance with 145.A.30(f). In this case the NDT inspector performs the NDT task and signs off the Work Order / Engineering Order. The CCS releases the works performed to the component (including NDT inspection) on an EASA Form 1. |
|
Specialised services |
The release of the maintenance carried out under ‘Specialised Services’ class rating has to be performed by “specialised services” certifying staff. |
The certifying staff is qualified following the procedures established by the organisation in compliance with EN4179, Part-66 licence is not required. |
The release of works performed under class ‘Specialised Services’ rating is done on an EASA Form 1 or using another form of release to service (other than aircraft release to service) as defined by the organisation in the CAE in compliance with CAO.A.070(a) and approved by the competent authority (AMC1 CAO.A.070 (a)(1)). |
A Part-CAO organisation holding a ‘Specialised Services’ approval on a particular NDT method. The approved scope of work will be NDT inspections on this method. |
Note: In case of non-EU organisations approved by the EASA in accordance with Part-145, the Part-66 licence could be read as “Part-66 or national licence in accordance with Part-145 Appendix IV”