Appendix V — Maintenance Organisation Certificate referred to in Annex I (Part-M), Subpart F – EASA Form 3-MF
Regulation (EU) 2021/700
|
Page 1 of 2 [MEMBER STATE (*)] A Member of the European Union (**)
MAINTENANCE ORGANISATION CERTIFICATE Reference: [MEMBER STATE CODE (*)].MF.[XXXX]
Pursuant to Regulation (EU) 2018/1139 of the European Parliament and of the Council and to Commission Regulation (EU) No 1321/2014 and subject to the conditions specified below, the [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] hereby certifies:
[COMPANY NAME AND ADDRESS]
as a maintenance organisation in compliance with Section A, Subpart F of Annex I (Part-M) to Commission Regulation (EU) No 1321/2014, approved to maintain the products, parts and appliances listed in the attached terms of approval and issue related certificates of release to service using the above references and, when stipulated, airworthiness review certificates after an airworthiness review as specified in point ML.A.903 of Annex Vb (Part-ML) to Commission Regulation (EU) No 1321/2014 for those aircraft listed in the attached terms of approval.
CONDITIONS:
1. This certificate is limited to what is specified in the scope of work section of the approved maintenance organisation manual as referred to in Section A, Subpart F of Annex I (Part-M) to Commission Regulation (EU) No 1321/2014; and 2. This certificate requires compliance with the procedures specified in the approved maintenance organisation manual; and 3. This certificate is valid whilst the approved maintenance organisation remains in compliance with Annex I (Part-M) and Annex Vb (Part-ML) to Commission Regulation (EU) No 1321/2014. 4. Subject to compliance with the foregoing conditions, this certificate shall remain valid until 24 March 2022 unless the certificate has been surrendered, superseded, suspended or revoked before that date.
Date of original issue: ......................................................................................................................................... Date of this revision: .......................................................................................................................................... Revision No: …………………………………………………………………………………………………………………………………………………. Signed: ...............................................................................................................................................................
For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] |
EASA Form 3-MF Issue 6
(*) Or 'EASA' if EASA is the competent authority
(**) Delete for non-EU Member States or EASA.
|
Page 2 of 2 MAINTENANCE ORGANISATION TERMS OF APPROVAL
Reference: [MEMBER STATE CODE (*)].MF.XXXX
Organisation: [COMPANY NAME AND ADDRESS]
|
||||
|
|
CLASS |
RATING |
LIMITATION |
|
|
|
AIRCRAFT (**) |
(***) |
(****) |
|
|
|
(***) |
(****) |
|
|
|
|
ENGINES (**) |
(***) |
(***) |
|
|
|
(***) |
(***) |
|
|
|
|
COMPONENTS OTHER THAN COMPLETE ENGINES OR APUs (**) |
(***) |
(***) |
|
|
|
(***) |
(***) |
|
|
|
|
(***) |
(***) |
|
|
|
|
(***) |
(***) |
|
|
|
|
(***) |
(***) |
|
|
|
|
(***) |
(***) |
|
|
|
|
SPECIALISED SERVICES (**) |
(***) |
(***) |
|
|
|
(***) |
(***) |
|
|
|
These terms of approval are limited to the products, parts and appliances and to the activities specified in the scope of work section of the approved maintenance organisation manual. Maintenance organisation manual reference: ................................................................................................. Date of original issue: ........................................................................................................................................ Date of last revision approved: ........................ Revision No: …………………………………………………………………….. Signed: ............................................................................................................................................................... For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] |
||||
EASA Form 3-MF Issue 6
(*) Or 'EASA' if EASA is the competent authority.
(**) Delete as appropriate if the organisation is not approved.
(***) Complete with the appropriate rating and limitation.
(****) Complete with the appropriate limitation and state whether the issue of airworthiness review certificates is authorised or not (only possible for ELA1 aircraft not involved in commercial operations when the organisation performs the airworthiness review together with the annual inspection contained in the AMP).
Appendix VI — Continuing airworthiness management organisation certificate referred to in Annex I (Part-M) Subpart G – EASA Form 14-MG
Regulation (EU) 2021/700
|
[MEMBER STATE (*)] A Member of the European Union (**) CONTINUING AIRWORTHINESS MANAGEMENT ORGANISATION CERTIFICATE Reference: [MEMBER STATE CODE (*)].MG.XXXX (ref. AOC XX.XXXX)
Pursuant to Regulation (EU) 2018/1139 of the European Parliament and of the Council and to Commission Regulation (EU) No 1321/2014 for the time being in force and subject to the condition specified below, the [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] hereby certifies: [COMPANY NAME AND ADDRESS] as a continuing airworthiness management organisation in compliance with Section A, Subpart G of Annex I (Part-M) of Regulation (EU) No 1321/2014, approved to manage the continuing airworthiness of the aircraft listed in the attached terms of approval and, when stipulated, to issue recommendations and airworthiness review certificates after an airworthiness review as specified in point M.A.901 of Annex I (Part-M) or ML.A.901 of Annex Vb (Part-ML), and, when stipulated, to issue permits to fly as specified in point M.A.711(c) of Annex I (Part-M) to that Regulation. CONDITIONS 1. This certificate is limited to that specified in the scope of work section of the approved continuing airworthiness management exposition as referred to in Section A, Subpart G of Annex I (Part-M) to Regulation (EU) No 1321/2014. 2. This certificate requires compliance with the procedures specified in the continuing airworthiness management exposition approved in accordance with Subpart G of Annex I (Part-M) to Regulation (EU) No 1321/2014. 3. This certificate is valid whilst the approved continuing airworthiness management organisation remains in compliance with Annex I (Part-M) and, if applicable, Annex Vb (Part-ML) to Regulation (EU) No 1321/2014. 4. Where the continuing airworthiness management organisation contracts under its Quality System the service of an organisation or several organisations, this certificate remains valid subject to such organisation(s) fulfilling applicable contractual obligations. 5. Subject to compliance with the conditions 1 to 4 above, this certificate shall remain valid until 24 March 2022, unless the certificate has previously been surrendered, superseded, suspended or revoked. If this form is also used for licenced air carriers in accordance with Regulation (EC) No 1008/2008, the Air Operator Certificate (AOC) number shall be added to the reference, in addition to the standard number, and the condition 5 shall be replaced by the following extra conditions 6, 7 and 8: 6. This certificate does not constitute an authorisation to operate the types of aircraft referred in condition 1. The authorisation to operate the aircraft is the AOC. 7. Termination, suspension or revocation of the AOC automatically invalidates this certificate in relation to the aircraft registrations specified in the AOC, unless otherwise explicitly stated by the competent authority. 8. Subject to compliance with conditions 1 to 4, 6 and 7, this certificate shall remain valid until 24 March 2022, unless the certificate has previously been surrendered, superseded, suspended or revoked.
Date of original issue: …………………………………………………………………………………………………………………………………. Signed: ……………………………………………………………………………………………………………………………………………………….. Date of this revision: ……………………………………………………. Revision No: ……………………………………………………….. For the Competent Authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] Page 1 of 2 |
EASA Form 14-MG Issue 6
|
Page 2 of 2 CONTINUING AIRWORTHINESS MANAGEMENT ORGANISATION TERMS OF APPROVAL
Reference: [MEMBER STATE CODE (*)].MG.XXXX (ref. AOC XX.XXXX)
Organisation: [COMPANY NAME AND ADDRESS]
|
|||||
|
|
Aircraft type/series/group |
Airworthiness review authorised |
Permits to fly authorised |
Organisation(s) working under quality system |
|
|
|
|
[YES/NO] (***) |
[YES/NO] (***) |
|
|
|
|
|
[YES/NO] (***) |
[YES/NO] (***) |
|
|
|
|
|
[YES/NO] (***) |
[YES/NO] (***) |
|
|
|
|
|
[YES/NO] (***) |
[YES/NO] (***) |
|
|
|
These terms of approval are limited to that specified in the scope of work contained in the approved Continuing Airworthiness Management Exposition section ………………………………………………………………………… Continuing Airworthiness Management Exposition Reference: ………………………………………………………………….. Date of original issue: …………………………………………………………………………………………………………………………………. Signed: ……………………………………………………………………………………………………………………………………………………….. Date of this revision: …………………………………………………………… Revision No: …………………………………………………
For the Competent Authority: [COMPETENT AUTHORITY OF THE MEMBER STATE *]
|
|||||
EASA Form 14-MG Issue 6
(*) Or EASA if EASA is the competent authority
(**) Delete for non-EU Member State or EASA
(***) Delete as appropriate if the organisation is not approved.